Interior doors can be restored. How to restore interior doors? Isn’t it easier to buy new wooden doors?

If you look with horror at your interior doors with peeling paint that no longer hides imperfections with adhesive film, chips and cracks, but your budget is down to the last penny, it’s time to start restoration. It is this measure that will allow you to quickly and efficiently restore the canvas without resorting to purchasing new doors.

Typically made from plastic, glass, wood and its derivatives. And there are a lot of different restoration methods, but the most important stage is cleaning and preparing the canvas. It is important to carefully remove all traces of paint, grease, old seals, and level the door so that the door looks like new in the future.

We are preparing a wooden door for restoration. Removing fittings and paint

The first thing to do is to carefully remove the door from its hinges and place it on the floor or four stools.

Hinges can be invisible, mortise, screw-in, card removable or non-removable. Since the entire door leaf will be restored, the hinges must be temporarily completely dismantled. To do this, unscrew all the bolts and caps, pry the door from below with a crowbar, lift it, remove it and set it aside.

In addition to the hinges, you should remove all other fittings that will interfere with further work.

Video - How to quickly remove a door from its hinges

How to remove paint. Method one - grinding

If the door is flat and there are a lot of layers of paint, you should take the canvas outside and try to clean it grinder. The work is quite dusty, the grinding wheels quickly become clogged, but the result will not be long in coming.

The second method is the use of chemistry

You can find various solvents and old paint destroyers on sale. One of them is B52. Operating principle: wetting the surface, waiting, cleaning the peeled coatings with a spatula.

In addition to the fact that this work is very hard and harmful (solvent vapors are unsafe for health), it is worth noting that chemistry cannot cope with big amount layers of old coating. Therefore, this method is only applicable for cleaning small plots doors with a thin layer of old paint.

You can make your own paint remover mixture by mixing caustic soda, water and oatmeal to a thick consistency. This slurry should be distributed over the canvas, and after 30-50 minutes, cleaned off with a metal spatula along with the swollen paint layer.

It is important to use gloves and a respirator!

Method three - using a gas burner

For reasons fire safety, work must only be carried out outdoors. Paint heated by a torch comes off easily, but at the same time it can smoke and emit pungent odors.

This method is applicable only if you know how to handle a burner, have prepared a sufficient supply of cylinders and are ready to warn your neighbors about the upcoming work.

Method four - using a hair dryer

This method is the most productive and safe. Even if there are layers of paint on the door that were applied several decades ago, they will peel off easily, and there will be no burning or chemical smells during operation.

Heat the paint and scrape it off with a sharp spatula. Be careful not to damage the wood. Do not lean over the door, as the air temperature is about 600 degrees.

Method five - soft blasting

The method involves gentle, careful removal of complex contaminants and old paint and varnish coatings from metal, glass, and wood. In this case, the door leaf will not be damaged. When working in conjunction with a jet of compressed air, Armex biodegradable cleaning agent will be applied to the surface of the door.

The main disadvantage of this seemingly ideal method is the inability to perform work at home, the need to deliver the door to a workshop and the associated costs.

Method six - Using a drill and attachment

Stores sell special abrasive brush attachments that fit onto the drill. Metal fibers will remove old paint, but may damage the wood of the canvas. To process the entire door, you may need not one, but several replacement nozzles, the cost of which is 120-170 rubles per piece.

Video – Soft blasting

Plastering a wooden door

After all layers of old paint have been removed, you should take sandpaper, secure it to the holder and carefully sand the door, making movements along the grain line. This measure will allow you to remove paint from hard-to-reach areas, smooth out scratches and chips.

After sanding, vacuum the door and wipe it with white spirit, degreasing it.

Open the can of primer, mix and apply a thin layer of the mixture to the door. will extend the life of the wood and serve as the basis for a new paint coating. Average consumption primers - 100 grams per 1 square meter of canvas. The average price of a package weighing 2.5 kg is 280-350 rubles.

Using a narrow spatula, apply the mixed wood putty. Distribute it and leave to dry. After this, you will have to sand the entire door again with fine-grained sandpaper to eliminate all the smallest defects.

If there is a large, deep crack on the door, it can be eliminated by selecting a piece of wood that is suitable in size and color. We coat the sliver with wood glue and firmly drive it into the crack. After about a day, the glue will dry and the door will be ready for priming, puttying and painting.

Prices for popular types of putty

Putties

Strengthening the door

If your door has dried out from age and is no longer strong enough, it is recommended to strengthen the door leaf and frame. And this must be done immediately after the preparation, but before the staining process.

If the blade is deformed, a plane will help correct the geometry. We remove excess wood with a tool, simultaneously checking the accuracy of the corners with a carpenter's metal square.

If the door had dried out and closed very loosely, a large gap was visible between the door leaf and the frame, it is necessary to cut a thin strip from plywood or board and nail it to the end of the door being restored. Then we process the rail with a file or plane, precisely adjusting the dimensions.

You can strengthen the door leaf with metal corners. But so that the door does not lose its attractiveness, it is worth paying attention to the decorative carved corners and installing them (nail them with thin nails or fix them with self-tapping screws) after painting the canvas. Don't forget to buy a new one door handle, stylistically matching the curly corners.

Replacing cracked glass

Cracked or simply outdated cloudy glass is not difficult to replace with your own hands. In its place, you can install a new one, for example, matte or transparent, tinted or with a sandblasted pattern, embossed or smooth, colored or plain.

Note! If the glass has a thickness of 10 mm (triplex), then replacing it is impractical. Firstly, it is very expensive, and secondly, it is almost impossible for an inexperienced person to cope with such a task on their own.

Case 1. Glass fixed with glazing beads

The easiest way is to replace glass secured with glazing beads. It is enough to dismantle them and then remove the glass by hand. We arm ourselves with pliers and a metal spatula. We pry up the glazing bead with a spatula, and use pliers to carefully pull out the nails.

Use a chisel or knife to clean the glass bed. We take measurements. If the opening is non-standard, we make a figured pattern from cardboard. At the same time, we take into account that the size of the glass should be slightly smaller than the opening. We wipe the glass with a soapy sponge, dry it with a clean rag, transfer the design from the pattern and cut it.

Attention! Wear gloves to avoid cutting your hands. Carry out work on a flat surface with a working glass cutter.

We treat the perimeter of the glass opening with sealant, after which we insert the cut piece, saw new glazing beads with a jigsaw and fasten them with thin nails.

Case 2. The glass has a hidden fixation

If the glass has a hidden fixation, you will have to disassemble the door, unscrewing the bolts, removing the old glass and inserting the new one. Silicone cannot be used in this case, since it will be impossible to replace it later. A significant disadvantage of replacing glass in such doors is that after assembly, the panel may lose its geometry and will require editing with a plane.

By the way, instead of glass, you can use an acrylic unbreakable mirror. It is quite light, durable, highly decorative and easy to cut.

Find out about 10 best options, how to do from our new article.

Painting the door

A door prepared in accordance with all the rules can be painted. We carry out the work in two stages - applying a base layer of white paint and tinting.

We choose matte paint for wood, apply it with a spray gun or brush, moving the brush along the grain. Apply one layer, making sure that no smudges appear.

Important! If there is a glass insert, be sure to seal it with masking tape so as not to stain the surface with paint.

For tinting, choose glossy or matte paint any color, for example dark brown. We paint the canvas in the same way. If necessary, apply another layer, but only after the previous one has dried. The more layers of paint, the more saturated the shade will be. But don’t get carried away and create too thick a coating.

Important! Be sure to prepare and restore the door frame. Otherwise, the updated door will contrast unfavorably with the adjacent wooden surfaces.

When the paint has dried, you can apply a layer of glossy varnish or begin installing door handles.

Prices for construction paint

Construction paint

Video – Do-it-yourself door restoration

Video - Master class on restoration of an interior door with a glass insert. Glass replacement

You can restore not only wooden ones, but also. Before work, it is advisable to remove the canvas and lay it horizontally. This will make the job easier.

Step 1. We dismantle or cover the door handle, peephole, and other fittings with masking tape.

Step 2. Use a wire brush or drill with an attachment to remove all traces of corrosion. Sand the surface with sandpaper (grit 80-150). We vacuum the canvas and treat it with a solvent.

Step 3. Treat the door with car polish. It is not recommended to use wood fillers as they do not adhere well to metal. Car polish will hide all dents and micro-scratches formed after cleaning the rust. Smooth out the applied polish with a spatula. The drying time of the composition is about 30-40 minutes.

Step 4. Polish the entire surface of the door with 400-grit sandpaper. Wipe the door with a clean damp cloth, and then degrease using a grease remover.

Step 5. Apply an anti-corrosion primer for metal to the door. It is convenient to use a roller and a narrow brush. After the primer layer has completely dried, we sand the canvas again with fine-grained sandpaper.

Step 6. Paint the door with metal paint. There can be several layers, but each subsequent layer is applied only after the previous ones have dried. To apply paint we use a roller and brushes or a spray gun. Don't forget about gloves and a respirator.

Similarly, we clean and paint the door frame, then remove the masking tape, install the fittings and hang the door in its rightful place.

In this way, you can not restore the entire surface of the door, but only a small area, but it is important to choose tone-on-tone paint.

How to laminate an interior door with film

It is better not to use cheap ones for pasting doors. PVC film, but give preference to the durable “self-adhesive” D-C-FIX. This film is guaranteed to last more than 10 years, will not fade in the sun and will not wear out.

The film is sold in rolls with a width of 45, 90 and 67.5 cm. The length of the roll is 15 m. The average retail price of this German film is 1,700 rubles. From a huge assortment, it’s not difficult to choose an option with imitation wood, stone, abstract or other patterns that suit a specific interior.

The film should be glued carefully, with someone's help. It is advisable to cut according to patterns, and immediately remove small bubbles with a wide plastic spatula. If the bubble does not go away, you can puncture it with a thin needle. For better plasticity, the film can be heated with a hairdryer.

Note! can be restored using adhesive-based veneer. We press the material to the canvas and heat it with an iron. We cut off the excess. We leave the restored door leaf for a while, pressing the glued veneer with sandbags.

Prices for self-adhesive film

Self-adhesive film

Video - Pasting MDF with veneer

Video - How to glue D-C-FIX film

Video - The principle of gluing film

How to replace door hinges. Photo instructions

Video - Installing hinges on an interior door

Since you’ve come to this page, you’re probably faced with the question of how to update interior doors with your own hands - you’ve either thought about their major restoration, or you’ve simply decided to update the interior of the room in this way. In any case, you have come to the right place and will find a lot of useful information in this article. Together with the site, we will deal with different ways, allowing, if not to completely put the interior doors in order, then at least partially restore them and give them a new, fresh look.

Do-it-yourself interior door finishing photo

How to update interior doors with your own hands: partial restoration

Behind long years During operation, various defects and damage appear on the surface of the doors - if handled carefully they are minor, but if handled carelessly they are large and deep. In any case, all this damage pretty much spoils appearance not only the door itself, but also the room as a whole. They, of course, can be painted, but over time, layers of paint worsen their condition - besides, not every door can be refreshed in this way. For example, instances cannot be updated in this way. Let's look in more detail at how you can perform a partial restoration of doors depending on their decorative covering.

You can see similar options for updating an interior door in this video.

Unfortunately, there are no other methods of partial restoration today - even the global technology for restoring an old door is based on these principles. To be precise, this is the mechanical removal of minor damage, filling of large potholes and application of a new decorative coating. In this way, a door, especially a wooden one, can be made almost indistinguishable from a new one.

How to update an old interior door with your own hands: home “lamination”

This, of course, is not factory lamination, and you cannot count on a long service life with this method of solving the question of how to update an interior door, but it allows you to give the doors an excellent appearance that will last for several years. In general, the option is cheap, but not cheerful - the end result looks quite elegant, especially if you put in maximum effort during the work process. This method consists of simply gluing doors with a film on a self-adhesive base. Despite the apparent simplicity of the work, this is not a simple matter and requires knowledge of certain subtleties and nuances. To make it easier to understand how this process is carried out, let’s consider it point by point - from “A” to “Z”.

In all other respects, the issue of finishing interior doors with your own hands with self-adhesive film does not cause any difficulties. The only thing that still needs to be understood here is that pasting over the installed door block It’s inconvenient, and most importantly, it won’t be possible to do it efficiently if the question is posed this way. In a good way, the block needs to be dismantled and disassembled into parts - as they say, disconnect everything that is possible from each other. This is the only way to achieve high-quality results.

And to conclude the topic of how to update interior doors with your own hands, a few words about alternative methods - you should not think that the options described above are the only and unique ones. Firstly, there is a huge variety of decorative paints, which can be called paints with a stretch - in fact, these are full-fledged decorative “plasters” that imitate an old cracked surface or a newfangled gloss. Secondly, decorative sheet material(for example, thin plastic), which can be used to cover solid doors. Also, it can be used as decoration. In general, there are plenty of options, and the most important thing is to see them. Imagine! And only then will you be able to give your doors a truly unique and inimitable appearance.

A modern interior door is not only about sound and heat insulation of a room. This is a full-fledged element of the interior, which plays an important decorative role. This is probably what manufacturers are guided by. building materials, setting door prices. No, it’s not that they are too high, but they are not low at all. But you really want all the details in the interior to match each other. For those who do not have extra material resources, but have good taste, imagination and a great desire to decorate their home, we will tell you how to decorate interior doors with your own hands. Please note that, most likely, in addition to the doors themselves, your attention will also be required door slopes, and, of course, the doorway.

Preparing interior doors for finishing

Regardless of which finishing method you like, the surface of the door leaf needs to be prepared. In the process of work you will need: high-quality adhesive composition, tracing paper and some object used as a press. First of all, the door leaf must be removed from the hinges and carefully checked for loose spots, cracks and voids. The peeled areas of the surface must be carefully and carefully covered with glue, covered with tracing paper on top and pressed down with a press. Small voids and cracks can also be easily eliminated using an adhesive solution. If there are deep cracks, you will have to tinker a little longer. They are usually filled with fine sawdust mixed with furniture varnish or construction adhesive.

Methods for finishing interior doors

The most simple ways interior door finishes are:

• painting;
• opening with varnish;
• staining;
• veneering;
• decoupage;
• craquelure.

Door painting

Finishing interior doors by applying paint to them is the most commonly used method of updating the door leaf. The work uses aqueous solutions of organic or synthetic dyes. The result of this coating is an updated, brighter appearance of the door. The solution must be selected based on the original color of the wood.

Opening with varnish

For varnishing doors, handymen prefer parquet varnish or Polish Lakobeits. Both options spread well and penetrate deeply into the wood. Lakobeits has an additional advantage - this composition combines both varnish and tinting base. The coating can be applied using a brush, roller or spray. However, experts recommend the first option, arguing that when moving the brush parallel to the door fibers or structure, the varnish is applied more evenly. To obtain a more aesthetic result, the door leaf is opened twice.

Staining

Quite often, when finishing the same door leaf, it is first treated with stain and then varnished. Staining allows you to achieve the desired shade of the door, and varnishing enhances the brightness of the texture. Subsequent sanding gives the canvas a matte finish. If for some reason you are not satisfied with the matte surface, then after grinding it is necessary to polish and dry it. As a result, the interior door acquires mirror shine and practically no different from those on display. Veneering

With the help of veneering, old doors made from shavings, sawdust or low-value wood can become new life and look like an expensive, elegant, high-quality product. The main requirement is careful preparation of the canvas, namely sanding. The veneer is directly glued across the grain or diagonally.

Vinyl sticker decal

If you do not consider yourself a jack of all trades, choose the simplest and cheapest option for finishing an interior door vinyl stickers. This method is especially good when you just need to hide a scratch or minor damage to the door leaf. Armed with a soft cloth, a hairdryer and stationery scissors, you can update the door in a matter of minutes. Treat the surface before applying vinyl. There should be no dirt or grease.

Next, carefully align the sticker and separate the design from the backing on which it is attached. The image itself is glued like wallpaper, which is carefully smoothed with a napkin to avoid the formation of bubbles. 10-15 minutes after the vinyl has occupied the allocated area of ​​the door, carefully, slowly, so as not to damage the pattern, remove the mounting film covering the sticker. If the film is difficult to remove, warm it up a little with a hairdryer. Using a hairdryer, annoying vinyl stickers can be easily removed from any surface.

Decoupage of interior doors

The technique of decoupaging interior doors is not much more complicated. Diligent housewives will be able to carry out such finishing on their own, since the door leaf does not even need to be removed from the hinges.

Preparation of doors in in this case standard – washing and drying. Next, in order not to stain the adjacent space, you can stick tape around the perimeter of the opening. The door leaf is carefully primed, rubbed with regular paraffin candles and painted. Now we move on to gluing decoupage cards, which must first be kept in cool water for 5-10 minutes. Before gluing, the remaining water must be removed with a napkin, then carefully apply PVA glue both to the inner surface of the picture and to the door itself.

After the card takes its place on the door leaf, you need to carefully check the result for wrinkles and bubbles, since such defects cannot be corrected later. When the drawing is completely dry, its edges are treated with a thin layer of white putty, the excess of which is carefully removed with sandpaper. Artificial light abrasions can be made on the edges of the door leaf and trim to make the door look retro.

Second, more economical option– decorate the door with elements cut from napkins. They are selected to match the room, glue is applied to the door and the same is done with the fragment. The napkins are glued to the doors, smoothed out, allowed to dry, and then the door is covered with acrylic varnish.

Craquelure

This type of interior door decoration is an original option, ideal for antique lovers. Considering that such finishing is rare, your interior will be more than original. The craquelure technique involves applying two layers of varnish. In this case, varnishing compositions must be selected that differ in consistency and drying time. The surface of the door leaf for craquelure is prepared in the same way as for decoupage or gluing vinyl stickers, i.e. cleaned and degreased.

First, craquelure varnish is applied. After the first layer has completely dried, a specially aging varnish containing bitumen is applied on top of it. Bitumen is used to enhance the effect and more clearly highlight cracks on a light base. For dark surfaces use acrylic paint. The technology described above is considered the best.

In order to simplify the process, you can use a one-component craquelure varnish, which is covered with contrasting paint on top. And for those who prefer cheaper options, instead of craquelure varnish, you can use PVA glue, vinegar, gelatin and even egg white.

Decorating the door leaf

Change the look of the old one interior design It is also possible in other ways not related to the use of paints.

Photo wallpaper is special wallpaper for doors; installation instructions are included with the product. Disadvantage - there are only standard sizes, and they can only be used on a flat door leaf without panels.

Vinyl or paper wallpaper - can be glued either to the entire surface of the canvas or only to the panels. If the door structure is double-leaf, it is recommended to choose a symmetrical design.

Fabric - pasted as an applique on a panel, or in fragments, imitating patchwork. Care should be taken to ensure that the glue does not leave stains on the surface of the fabric when drying.

Finishing the interior door opening

We have already figured out how to give new life to an old interior door. But, you see, the openings also need to be put in order, otherwise the updated, beautiful door will simply look out of place.

Sections of the article:

A door is an interior detail that constantly experiences high loads. Naturally, after some time the former aesthetic appearance of the door leaf is lost. Various defects appear on the surface - scratches, cracks in the paintwork, dents, marks from dog teeth and claws. And if buying new doors is not an option, you should start restoring old doors. What this process is, what tools and materials are needed - we will tell you in our article.

The restoration process is quite complex, but quite feasible. There are a lot simple options restoration of interior doors.

Required materials and tools

Depending on what type of door has become unusable, a certain set of materials and tools should be prepared for restoration work. So, you definitely need antiseptic impregnation, varnishes and stains, paint removers, wood paint, putty and primer.

This is about materials. Now let's see what is needed from the tool. This is an electric drill, a set of spatulas, chisels and screwdrivers, a carpenter's knife, a roller, brushes, emery cloth, nails and a hammer, pliers, glazing beads, door fittings and a hair dryer.

Restoring a wooden door

Solid wood door panels natural wood worthy of praise - these are reliable, environmentally friendly products that have a very aesthetic appearance. But such structures are very cumbersome and it is very difficult to restore them. However, if the restoration technology is followed, the result is worth the effort. Natural wood lends itself well to restoration.

Preparation

The old door must be removed and laid horizontally on as level a plane as possible. If the canvas has upholstery and glass inserts, they should also be removed. Next, you need to move on to removing the paintwork - usually there are several layers of paint on such canvases. To remove the paint easily and quickly, you will need a hair dryer - the coating is heated until it swells, and then easily removed with a spatula. Remaining paint can be removed by sanding.

It is important not to overheat the door leaf while warming it up. As a result of overheating, wood can change its natural color. It is best to remove paint outside or in a ventilated room.

At the final stage preparatory work The entire canvas must be coated with a primer.

The main stage of restoration work

The first step is to carefully inspect the canvas - it often happens that after the preparation process some minor defects remain. To remove them, you can use putty. Based on the condition of the door leaf, it is processed partially in places of defects or completely. Then, after the putty has dried, it is sanded. Sanding is a fairly delicate process and should be approached with the utmost care. A surface is well sanded only when there are no traces of processing on it.

After sanding, dust and dirt may remain on the surface. Before painting the product, the surface is thoroughly cleaned. It is advisable to apply paint in two stages - at the first stage, the canvas is coated with enamels, then proceed directly to painting.

The first step is to select the color of the future door - it is recommended to use stains. They can be either water or oil based. Stain or enamel should be applied using a spray gun, but at home you can also use brushes and sponges. Clumps of stains and enamels should not be left on the surface - this can affect the color of the entire door leaf.

Paint or varnish is applied with a short-hair roller or brush. If it is a brush, then it should be of high quality and it is better if it is made of artificial material.

Last step

At this stage, all that remains is to install the door leaf in its rightful place. But the process is not limited to hanging the door leaf on the hinges and then aligning it. Sometimes door frame reinforced with reinforcing bars or anchor bolts. These manipulations are performed with the door closed. After installation, the gaps between the frame and the opening are filled with polyurethane foam.

The process of restoration of varnished door panels

Let's look at how you can restore an old lacquered door. The first step is to remove the old coating. The door is carefully sanded and then sanded in the direction of the wood grain.

It is better to apply new varnish using a flute brush or a foam swab. The varnish is applied in at least four layers with breaks. The second layer can be applied after 2-3 hours, but all the rest can be applied after 24 hours. All this time the room should be very well ventilated.

The resulting surface must then be polished - since this process is quite labor-intensive, it is recommended to use an angle grinder with a felt or felt polishing attachment.

We restore veneer doors

The first step is to measure the surface of the door leaf and cut the prepared veneer. Then glue is applied to the canvas and allowed to absorb for 10 minutes.

If the door is not level, then it needs to be leveled - for large irregularities use a plane, for small ones you can get by with an emery sheet. If there are chips or cracks on the surface, they are restored using putty.

For gluing veneer, an iron is used, the heating temperature of which is no higher than 50 degrees. After the veneer is heated, the surface is fixed by lapping. Then you need to press down the structure with a heavy object. It is important to carefully control the gluing process so that no voids form under the veneer.

Laminate flooring can be glued in the same way, but liquid nails should be used to secure it.

This method of restoring an old door has advantages - a wide selection of veneers, a long service life, and an acceptable cost. But such a coating is very sensitive to humidity and temperature changes.

Restoration of solid wood doors using MDF panels

The restoration process is very, very simple. MDF panels that match the interior style are glued onto the old door leaf. This is a popular method and it also has some advantages - for example, these panels look very aesthetically pleasing and are resistant to moisture and mechanical damage. The disadvantages are that the panels wear out in places where they are frequently exposed.

Restoration of fiberboard doors

The technology for restoring such door leaves is slightly different from working with door leaves made from solid natural wood. These differences are not very significant, but you should still know them.

Some sources indicate that you can use a blowtorch to remove a layer of paint - no, you should not use it. Only an iron or hair dryer is allowed. For sanding work, it is allowed to use only fine sandpaper - the fiberboard surface is quite thin. You can use decorative elements to slightly change the surface relief - it will imitate a paneled fabric. Then, after sanding, the entire door structure is painted.

There is another option. In this case, the surface will look like natural solid wood - for this, the surface is simply covered with veneer. How to restore an old door in this way is indicated above. After the work is completed, the door will simply be unrecognizable - everyone will think that it is made of real natural materials.

There are more complex ways, but they require certain skills. For example, a solid door can receive glass decorative elements. To do this, mark the place for future inserts, and then use a jigsaw to make a cutout. The resulting space is strengthened with slats. What the inserts will look like, how many there will be, depends only on the imagination of the master and the style of the interior.

Door frame and fittings

These door elements also need restoration work as urgently as the door itself. In addition, the fittings should be replaced. Experts recommend completely replacing the hinges to match the color of the restored door leaf, handles and lock. It is recommended to purchase only high-quality products - the service life and ease of use of the doors depend on their quality.

Many home craftsmen are sure that they can simply purchase and install a new box - but this is not so. Doors that have been in use for quite a long time have some deflections in different directions. When changing the box, you can only increase the gaps - it will not look aesthetically pleasing.

As you can see, restoration of old doors is possible. This is not a complicated process that you can do yourself. The materials that will be required during the manufacturing process can be purchased at construction hypermarkets - often their price is quite affordable. Such restoration allows you to save significantly - after all, even the simplest economy-class interior door costs from 4,000 rubles. In addition, old doors are high-quality products made from natural and solid wood, and after restoration they will look perfect.

The situation when interior doors become unusable and lose their appearance is not uncommon. Knowing a few basic techniques on how to update an old door will help you save a lot and not spend money ahead of time. Having learned how to restore the surface yourself, you can not only give your apartment a fresh look, but also turn interesting author’s ideas into reality.

By familiarizing yourself with a few useful secrets listed below, you will be able to do renovation work with your own hands. Do not forget about the importance of preparatory work, since this process also affects the beauty of the product. You can decorate the doors using paint, wallpaper, photo wallpaper, decoupage and other techniques.

Preparatory stage

Before you transform an old door, you must first prepare the surface and remove the previous coating. If you remove the product from its hinges in advance, it will be more convenient to carry out repair work. Place the door on a flat surface using a table or trestle. Remove from the canvas: handles, hinges, latches, locks. Replace parts with new ones if they become unusable. Don't forget to remove the glazing beads and remove the glass before starting repair work.

It will be much easier to act by adhering to the following points:

1. Using a heat gun, heat the surface to remove old paint much faster. When the layer begins to soften, use a putty knife to remove the coating.
2. Scratches and defects can be repaired using putty and wood putty.
3. Take sandpaper with different grits. Sand the surface and sand thoroughly.
4. You can completely renew old doors with your own hands if you apply drying oil or stain to the surface. This measure will protect the canvas from moisture and give the wood a beautiful shade.
5. Reinsert the glass into the door leaf and use new beads.

If you paint a door or glue wallpaper onto the canvas, do not forget to prime it first. Choose a special primer or thinly diluted glue.

Self-adhesive film

When ideas on how to cover an old door have reached a dead end, choose the simplest and most inexpensive option in the form of self-adhesive film. Geometric stickers can be distributed onto the canvas, even if you do not remove it from its hinges first. Choose a film of a bright shade to create a contrast with the overall tone. If you match the stickers to the color of the door, it will look tasteless.

Before gluing the film, use a pencil to mark where the patterns will be located. After this, apply the sticker to the canvas and use a rag to get rid of the air under the film, wiping it thoroughly. A canvas on which you can draw inscriptions with chalk will look very stylish and impressive. The cost of such a film is not cheap, but such an option will look very unusual.

Dye

In the process of updating an old door, as in the first case, it is important to use another inexpensive option - paint. Here you will have to remove the door from its hinges in order to paint the door as neatly as possible. You can choose absolutely any color - it all depends on your taste preferences and interior. Buy acrylic or water based, since it does not have an unpleasant odor. From alkyd paint It's better to refuse.

Experienced “artists” will be able to paint a door using dye in cans. For beginners, it is better to abandon this idea, since it will be difficult to apply the material in one tone, since the dye will be sprayed on different sides. If you choose a standard painting option, then use matte rather than glossy paint. In the second case, the dye will only highlight all the defects and unevenness of the canvas.

Before updating the doors without changing them, take a roller to make the painting process as comfortable as possible. A wide roller is suitable for smooth and solid doors. It is best to paint the doors in 2-3 layers, applying the paint with a fairly thin ball.

How to update an old door with wallpaper: several methods

It is not difficult to paste wallpaper onto the door leaf, and all stages of the work will not take much time. You can create a beautiful contrast if you choose wallpaper in a color that differs from the color of the walls. Having previously prepared the doors and primed them, you will be able to hang wallpaper according to the following scheme:

1. Dilute the glue according to the instructions on the package.
2. Spread the adhesive backing onto the canvas.
3. Carefully start gluing the wallpaper and do not forget to remove bubbles. A plastic or rubber spatula will help with this, which needs to be moved from the center to the edges.
4. Use a metal strip and a wallpaper knife to trim the edges of the wallpaper.
5. Wait until the wallpaper is completely dry to move on to the next decorating step if necessary.

If desired, apply additional decor on top of the wallpaper.

Molding

If, before updating the interior doors with your own hands (based on the photo with instructions), you purchase foam or polyurethane moldings, as well as sockets, then the decor will turn out to be quite unusual. This option will beautifully highlight a room decorated in a classic style. Using rounded moldings and a bright background you can decorate the room in Provence style.

After you have hung the wallpaper and it has already dried, use a pencil to mark where the moldings will be located. Using a tape measure, measure out how much material you will need to complete the decor. File the edges of the molding at an angle of 45 degrees. Then take PVA or other glue, treat the back surface of each element and glue along the markings. Wait for the glue to dry completely.

Photo wallpaper

Give the room a perfect look the new kind It will work if you stick photo wallpaper on the doors. This finishing option will look very bright and will help transform the interior of any room. You can order photo wallpaper from any printing house. In this case, it will be possible to individually select the design and type of pattern. Before updating old ones wooden doors do it yourself in a similar way, you should follow the previously given instructions for gluing ordinary wallpaper.

Antique effect

In the process of updating the old door, paint and sandpaper will be used to create the effect of antiquity. Before moving on to the decor, cover the canvas with dark paint in several layers. After this, apply light paint on top of the previous layer. When the paint is completely dry, take sandpaper and start sanding upper layer so that the dark paint shows through.

Using the craquelure effect you can also visually “age” the doors. To do this, use varnish or paint, which, after hardening, will visually form cracks.

Decoupage

Decoupage of an old door will look very beautiful if you use ordinary napkins for decoration. Before starting work, paint the canvas in White color. Then take a three-layer napkin with beautiful design and use scissors to cut out the image. Peel off the colored layer and carefully apply it to the door.

Dilute PVA glue and water in the required ratio and take a brush. Apply glue to the back of the design and attach it to the door. You can repeat this procedure several times until the entire application is completed. Finally, open the surface with acrylic varnish.

Glass inserts

Another good way how to update an old door with your own hands (using photos clearly) it’s worth trying to replace the glass. Install new glass in the door leaf or update the decor of the old one. The stained glass technique will look unusual.

Before painting the doors and creating an unusual stained glass window, prepare the following tools:

• stained glass paints;
• gloves;
• circuit;
• marker.

It is most convenient to paint glass in a horizontal position. Using a marker, draw the outlines, and then paint the middle on both sides. You can complete the picture entirely by gluing small stones or pieces of glass. These details should also be outlined with a black marker on top of the drawing.

Before you decorate an old door with your own hands, take this recommendation into account. Cut small holes in the door leaf and insert small multi-colored pieces of glass into the middle. This method will allow you to create beautiful composition from glass. This option is suitable if the door leaf is made of solid wood.

Stencil decor

Uncomplicated and yet nice option– door design using a stencil pattern. You can prepare the stencil yourself, or you can buy it ready-made at a hardware (stationery) store. Take thick paper and cut out the pattern you like. You can also prepare self-adhesive film in a similar way.

First, pre-treat the door, then take a stencil and carefully go over the top with a paint roller. Spray paint is also suitable for decoration. Make sure that the template fits tightly to the surface of the door, otherwise unnecessary smudges and stains will appear on the canvas.

Pre-paint the door white, and then use stencil patterns. Black and gold designs will look very beautiful on a light background. When updating interior doors with your own hands, also use a dark background and light stencil patterns.

Art drawing

Art lovers may want to pay attention to this unusual option door decoration. It is enough to first paint the doors in one tone, and then use additional paints and brushes for painting. The drawing can extend beyond the doorway by 10-20 cm and be a beautiful continuation of the composition.

If you don’t have any special talent, but want to restore an old door with your own hands, as in the photo, then first pick up a pencil. Draw a sketch with a pencil, and then start painting. Pre-cover the floor and walls with protective film to prevent splashes from damaging it. To create a memorable design, put paints in children's hands where they can express their creativity on canvas. Such art will give a sea of ​​positive memories and emotions.

Textile

In case you have no idea what can be done with old door no, but I really want to decorate it in an unusual way; the option with textiles is ideal. This is a very labor-intensive process, but the door design will turn out to be truly homely and cozy. Before you move on to arranging the door leaf, first buy fabric with the patterns you like. Avoid colors that are too light, as stains and defects will appear on such a surface very quickly.

Choose a material in the store whose color will blend as organically as possible with the rest of the decor. Use double-sided masking tape to make gluing textiles as convenient as possible. Distribute the tape around the entire perimeter of the door. Make sure that there are no folds along the edges of the door and that there are no patches.

Door lamination

You can update the appearance of the room if you apply film on the doors yourself at home. To do this, buy a self-adhesive film with an adhesive backing at a hardware store. First, pre-prepare the door leaf and cover scratches and uneven surfaces. If necessary, remove the old paint layer.

When gluing the film, do not forget that it bonds to the surface very quickly, so you will have to work very carefully to prevent the appearance of bubbles and unevenness. Apply the film gradually, millimeter by millimeter, using a plastic wallpaper spatula to prevent the appearance of defects.

By choosing one of the above options, it will not be difficult to update the door yourself at home. When decorating, it is important not to forget about the rest of the apartment’s interior and first protect it with film.