How to wallpaper in the corners of a room. How to glue wallpaper in corners - the secret to perfect gluing

Wallpapering walls is not a difficult task if the work is done on a prepared, flat surface. But difficulties often arise with gluing the material to internal and external corners. To avoid common mistakes, you need to become more familiar with the process technology of how to glue wallpaper and prepare necessary tools for fast work.

Necessary materials

Often, before wallpapering walls, preliminary preparation of the surface is required.

You only need to have:

• Wallpaper.
• Glue.
• Primer.

Main material - wallpaper, it is recommended to purchase one that is not very dense so that it is easy to glue. This is especially important when gluing corners. Before purchasing wallpaper, you need to calculate its quantity. To do this, the perimeter of the room is determined, the perimeters of window and doorways and a small margin is added (5-10%).

When choosing glue you need to be guided by the type of wallpaper. Therefore, when purchasing them, you must immediately take the appropriate glue. Primer will be required to ensure adhesion of the surface to the wallpaper.

Tools

The materials you need to obtain are:

• With a pencil.
• Metal ruler.
• With a tape measure.
• Painting knife.
• Plumb.
• With a sponge.
• With a brush.
• With a brush.

Where to start

After preparing the surface (cleaning it from dust with a brush and applying a primer), you can begin gluing the walls.

Pasting begins from the part of the room that is most visible. To do this, using a plumb line, you need to make the appropriate marks on the wall so that the canvases are strictly perpendicular to the floor. Then the distance from the ceiling to the floor is measured and pieces of wallpaper are cut to the required length with a small margin.

You cannot start gluing the first canvas from the corner.

You need to retreat a small distance (half the width of the wallpaper). Then paste wallpaper on the entire wall.

Depending on the type of wallpaper, the methods of applying glue differ. Some types involve applying an adhesive to the wallpaper, which must be absorbed within 5 minutes. After this, you can glue the canvas to a wall previously coated with glue. But other types of wallpaper should be glued dry, and only the wall should be smeared with glue.

External and internal corners should be pasted last.

Internal corners

Pasting an internal corner on 2 converging walls is done using the following technology:

• The distance from the corner to the pasted strip is measured on one wall, then on the other.
• Pieces are cut, the width of which has a margin of 2 cm.
• Carefully coat 1 piece of canvas with glue.
• Apply glue to the inner corner.
• The first canvas is pasted.
• The remaining strip is glued to the second wall.
• The wallpaper is being trimmed.

When gluing the first strip to one corner wall, you need to make sure that one side of the strip is flush with the wallpaper that was previously glued to the entire wall.

When applying the canvas, you need to carefully expel the air from under it. To do this, use a soft sponge to make smoothing movements from the center to the edge, moving from top to bottom.

The first strip for the corner is glued so that it extends 2 cm onto the 2nd wall. The canvas is ironed well in the very corner so that there are no air bubbles left there either.

After this, the 2nd strip is glued to the 2nd wall. It is glued using the same method as the 1st one and overlaps the already glued strip by 2 cm.

After this, you need to trim off the excess wallpaper. First of all, the wallpaper is cut at the top near the ceiling. To do this, apply a long spatula to the wallpaper at an angle to the ceiling and draw a strip along it with a sharp construction knife. After this, the excess part of the wallpaper is removed.

Then the same spatula is placed with the end part against the first wall that was glued, after which the spatula is slightly turned towards the corner. Then take a knife and use it to make neat cuts on the 2nd piece of canvas (it was glued to the 2nd wall).

You need to make light movements with a construction knife in order to make a cut only on the upper sheet without damaging the lower one.

Such movements must be done from top to bottom. Lastly, the part of the wallpaper at the bottom, which will be located under the baseboard, is trimmed.

But this was a presented method for gluing wallpaper on a corner in the case when wallpaper was already glued on 2 adjacent walls. Therefore, it is necessary to adjust the wallpaper to the edge of the last strip on one side and the other. But you can do it in another way: adjusting it to only one wall covered with paper.

The second way is as follows:

• The first strip is glued at an angle butt to the last strip.
• The excess part is placed on the second wall. On the second wall, 2 cm are measured from the corner in several places, and a vertical line is drawn.
• A construction knife is used to cut off 2 parts of the canvas.
• The same part is immediately applied to the corner with an overlap.
• Using a spatula and a knife, remove excess parts of the wallpaper that extend onto the first wall.

After gluing the second part of the canvas, you need to ensure that there are no distortions. After all, subsequent strips will be glued to this strip end-to-end and a misalignment may occur. Therefore, you need to constantly use a plumb line and a building level.

You can learn more about the process of gluing wallpaper on an inner corner in this video. Advice and recommendations from experts on each stage of work are presented.

External corners

The technology for gluing wallpaper on external corners is also based on butt technology. In order for the external corners to be ideal you will need:

• Glue the first strip, one edge of which will join the main panel on the wall, and the other edge will extend to the outer corner by 2 cm.
• Level the canvas.
• Glue the 2nd strip of wallpaper, one part of which will join the wallpaper of the 2nd wall, and the other part will overlap the first strip.
• Carefully level the canvas.
• Apply a long spatula to the glued 2nd sheet and cut off the excess part with a construction knife.

Do not forget about timely trimming of excess parts of the canvas from above and below. Often, when gluing the first canvas to the outer corner and extending it onto the second wall, folds appear.

To avoid this, you can use scissors to make cuts along the entire length of the canvas in the section of wallpaper that goes to the corner.

This will allow the strip to lie as flat as possible.

If wallpaper needs to be glued to an arched structure, then the technology is slightly different from pasting external corners. First, the strips extending onto inner part arches by 2 cm. It is necessary to immediately remove the excess parts of the approaches. Then the width of the inner part of the arch is accurately measured, and a strip of the required length is cut out and glued. In this case, there is no need to trim the glued strip because it was previously cut straight.

How to glue wallpaper with a pattern in the corners. Step-by-step instruction

Working with plain wallpaper is much easier than with patterned ones. But to liven up the room and get unusual design you will have to complicate the task and work with the selection of the pattern.

To apply wallpaper with patterns to external or internal corners, you need to adhere to the following technology:

• Take measurements of the first strip and cut it off.
• Measure 2 cm from the cut edge of the first strip and draw a thin line with a pencil. Fold the fabric along the marked line.
• Do the same work with the second piece that will be glued (also make a margin of 2 cm and bend the fabric along the line).
• You just need to first adjust the pattern, which will match in both canvases if they are bent along the lines.
• Then glue 2 strips on converging or diverging walls.

When gluing wallpaper with a pattern, you need to match the pattern as accurately as possible. Despite the fact that the corner is pasted over, all errors will be clearly visible.

To make the work easier, you can follow the advice of professionals:

• Buy wallpaper that is plain or has a small pattern. Due to this, you won’t have to spend a long time selecting a pattern on the corners.
• Using wallpaper with a large relief pattern, you can hide minor unevenness in the walls (or prepare the wall in advance and level the walls with plasterboard).
• For work, use only a sharp construction knife, otherwise it will be difficult to make an even cut on the canvas.
• Be sure to use the technology of wallpapering overlapping corners. If the canvases are glued end to end, they will separate over time.
• If, after gluing the canvas, excess glue passes through the joints, it must be immediately removed with a clean cloth. It is not recommended to use a hard brush, which can damage the top layer of material.
• Carry out the work carefully, because some types of wallpaper are afraid of getting glue on them.

Anyone can master the technology of wallpapering corners. If you follow the instructions, be careful and take your time, you can easily paste wallpaper not only on the internal and external corners, but also on arched structures and around window openings.

If you decide to make repairs, get ready for a complex process that will take a lot of time and effort. And turning to professionals will also be costly in terms of finances. Therefore, in order to save your money, we suggest doing at least part of the work yourself. For example, you can easily cope with such a process as wallpapering walls. The only difficulty you will have to face is the design of the corners of the room. As a rule, this work always causes difficulties.

Unfortunately, both apartment owners in old buildings and new buildings encounter uneven corners. Often there are defects on the walls that prevent you from hanging wallpaper beautifully and quickly. What to do in such a difficult situation and how to glue wallpaper in the corners? Below you will learn about all important points, and for clarity you can watch the video.

If you are gluing external corner protrusions, make sure that the wallpaper fits tightly to the wall, so it is not recommended to glue the entire strip to the corner at once.

If the joint of the walls is bad, it will simply gather in ugly folds. Moreover, the wallpaper should never end in a corner. It is necessary to leave an overhang of approximately 3 cm (if necessary, trim it with a knife). This way you can achieve a perfectly even pasting. When using thick wallpaper to decorate walls, use a plumb line.

If there are switches or sockets nearby, remove their covers and turn off the electricity. Next, glue the canvas on top, then cut out circles of smaller diameter than the casing itself. When finished you can put them back.

Preliminary preparation

It’s worth noting right away that all the preparation needs to be done long before gluing the wallpaper in the corners. First you need to remove the old finish and level the surface. To align the joints of the walls, use plastic corners, securing them with putty.

Then the surface is treated with a primer, which can be found in every hardware store. The primer is applied with a roller or brush.

How to glue wallpaper in corners: technology

You cannot cover all corners at once. Choose the one from which the work begins. To do this, prepare a strip of the required length and, depending on the type of wallpaper, apply the adhesive to both one wall (when gluing with non-woven wallpaper) and the wallpaper (in the case of vinyl wallpaper). If you use plastic corners, you need to coat them with glue.

When processing the wall surface, it is necessary to cover an area slightly wider than the wallpaper (minimum 5 cm).

Then you can start gluing the first canvas. If you are going to start pasting from left to right, you need to apply the left side of the canvas to the corner. The strip of wallpaper is located exactly along its entire length.

Then the canvas must be carefully leveled and all the air expelled from it. This can be done using a plastic spatula or a special roller. After this, the entire wall is covered up to the next corner.

Internal corners

Internal corners are most common in rooms. To properly paste them, you must adhere to these recommendations.

The strip must be glued so as to cover not just the corner itself, but also several centimeters of the adjacent wall. Next, it is important to press and smooth the wallpaper well using a lint-free cloth or sponge.

Then, using a ruler or tape measure, measure the width of the wallpaper on the adjacent wall from the top corner, turning it back 3-4 cm. This is necessary so that you can glue the strip overlapping the previous one. Further along these points, using a plumb line or level, you need to draw a line along the wall. The canvas glued to it will be strictly vertical.

By resorting to this technology for gluing the inner corners of the room, you can make the joint in these places invisible.

External corners

Almost every room has external corners (slopes). For easy and high-quality gluing, it is necessary to pre-level them using plaster. But this will not always be possible. In this case, without overlapping pasting, you will not be able to achieve the desired result. Let's look at how to wallpaper the outer corners in more detail.

First, you need to glue the wallpaper so as to cover 3-4 centimeters of the adjacent wall. Moreover, it is important that the wallpaper fits evenly and tightly to the wall and corner. For this reason, if necessary, prune them in several places.

After smoothing the canvas, cut off any excess wallpaper (vertically) using a sharp blade or knife, leaving a thin edge.

Then measure the width of the roll with a large ruler or tape measure and, stepping back about 5 mm, draw a vertical line using a plumb line or level. The next strip is glued along it. It will lie flat. As a result, you will end up with a slight overlap. It will hide all defects that arise after cutting the first strip.

Features of gluing wallpaper with a pattern

If your wallpaper has a pattern that has good clarity (for example, some geometric figures and shapes, vertical or horizontal stripes), you need to make sure that wallpapering in the corners does not distort it in any way.

Most likely, you will not be able to completely eliminate the pattern shift, which will result in a slight distortion remaining. But only you know about this drawback. To identify it, you need to carefully examine the connecting lines of the walls. If you strictly follow the instructions on how to properly glue wallpaper, the canvases will lie exactly vertically, and minor distortions of the pattern will be unnoticeable.

How to glue wallpaper in the corners of a room: some secrets

• If your wallpaper is heavy and thick, it would be a good idea to arm yourself with strong adhesive. It will be good if it is transparent.

Sticking to our simple tips You will wallpaper the corners of the room perfectly. Moreover, they will look beautiful, even uneven wall joints. You just need to be patient and do all the work carefully.

Wallpapering the walls of an apartment is a common procedure for most residents of our country. This is the most affordable and easy way interior renovations, but not many owners understand how to properly glue wallpaper in the corners of the room. This seemingly simple task encounters a lot of difficulties when it is necessary to paste over corners with an uneven surface. There are especially many problems with wallpaper that requires adjustment to the pattern. It will not be possible to achieve an exact match of the image in a crooked corner, and the overall picture will be hopelessly spoiled. You can endlessly join individual canvases on the wall, but without carefully leveling the surface in the corner and preliminary preparation, it will be impossible to achieve an acceptable result.

To avoid difficulties in the process of gluing wallpaper, you should pay attention Special attention preliminary preparation of walls and corners. Even minimal protrusions or depressions in the corner can cause serious distortion over a meter length, and several such errors make adjustment impossible - creases and tears appear, as a result of which it is impossible to match wallpaper with different patterns.

To prepare the surface for wallpapering in the corners, you will need to do the following:

1. The first step is to clean the surface of old coatings, dust and dirt.
2. If small depressions are found, they are eliminated using putty.
3. If the wall is uneven, you need to find the point of maximum protrusion at the inner corner. Using the guide rail ( metallic profile), installed along a plumb line or level to the adjacent wall, a mark is applied along which the corner is leveled with special building mixtures.
4. If it is impossible to level the inner corner with mortars, it is recommended to install a special corner made of metal mesh, after which it is necessary to plaster the corrected area. You can prepare the outer corner in the same way.
5. Leveled and dried surfaces must be treated sandpaper until a smooth surface appears.
6. After obtaining an ideal surface, it needs to be treated with a primer. This point in preparing the corner for gluing is mandatory, although many owners who carry out repairs with their own hands ignore this procedure. The surface treated with primer allows you to achieve more high degree adhesion of materials, which is especially important when working with corners.

The preparation carried out will allow you to solve the question of how to paste wallpaper in the corners of a room with high quality. In the same way, it is recommended to prepare complex surfaces in areas where doors, heating radiators and windows are located.

How to tape corners

To successfully overcome the problem of corners, both external and internal, it is necessary to prepare a set of tools that will allow you to complete this work with less effort. The following tools will be needed for gluing paper, non-woven and vinyl wallpaper:

• a plumb line or level to determine the vertical mark;
• a wide spatula as a basis for evenly cutting wallpaper;
• stationery knife;
• brush 150 mm wide;
• roller, preferably with a long handle;
• pencil;
• scissors;
• rubber roller for rolling wallpaper;
• container for diluting glue and primer;
• bath with a cuvette for working with a roller.

The technology for gluing internal and external corners in a room, proposed below, is valid only for plain products without a pattern, which do not require matching the image.

Domestic

It is best to seal internal corners using overlapping technology. To do this, you need to prepare a sheet with a width exceeding the width of the wall at the junction with the corner by 3-4 cm. This piece is intended for gluing the corner and slightly extending onto the adjacent wall.

After gluing the sheet, it is necessary to draw a strictly vertical line along this strip at a distance of 0.5 cm from the corner. This mark will serve as a guide for sticking the second sheet on the adjacent wall. To obtain a vertical line, use a plumb line or a laser level.

The second sheet is glued so that its edge coincides with the vertical mark. If the seam is invisible, you can proceed to further pasting of the walls; if it protrudes noticeably, you will have to make a leveling cut, for which you use a utility knife and a wide metal spatula as a guide surface for the knife.

After trimming, the excess strips are removed, the wallpaper is slightly spread at the joint and additionally coated with glue, after which it is joined again.

External

Modern projects practically do not provide for external corners in the apartment space, but in previous series such corners exist, so you should consider step by step instructions pasting of such walls:

1. As in the case of the internal corner, it is necessary to prepare a trellis with a width exceeding the wall space up to the corner by 4-5 cm;
2. The wallpaper sheet and the surface that is planned to be pasted over are coated with glue;
3. The trellis is glued to the main place and carefully leveled, removing air pockets;
4. After strengthening the sheet on the main wall, begin to fold the wallpaper along the corner. If necessary, small incisions can be made to smooth out wrinkles that form when the surface is uneven;
5. The next step is to make markings on the strip, departing from the angle of 0.5 cm. The markings must be strictly vertical, for which it is recommended to use a plumb line or a laser level;
6. Apply glue to the second sheet and the wall, after which, aligning the edge of the sheet along the line, stick it on;
7. Using a guide (a wide spatula, a long metal ruler or profile), a vertical cut is made in the middle part of the connected parts;
8. The cut strips are removed, and the joint area is additionally coated with glue and rolled with a rubber roller.

Every master who deals finishing works, there is a set of optimal solutions to issues that arise during the pasting process. Below are tips from professionals to help you understand how to properly glue wallpaper in corners and avoid mistakes:

• To paste walls with dense roll materials, you should use the most durable types of glue, and you need to choose glue with a transparent structure;
• Applying primer to the entire surface of the walls, and especially at the joints, is mandatory;
• Often, adjusting the pattern at the joint takes a lot of time, which leads to the glue drying out; therefore, it is necessary to add the adhesive in time in places where it has dried out;
• In old panel houses Significant deviations may be found in the corners. In this case, it is difficult to achieve effective alignment, so to make the work easier, you should purchase wallpaper without a pattern to avoid adjustment;
• If there is no special primer mixture, it is recommended to use wallpaper glue to treat the surface before gluing. It is enough to apply it 5 hours before the start of the main work, as a result of which the setting of the materials will be much more reliable;
• Coat the corners with a brush. The roller will not be able to cope with the complete processing of the entire surface of this unit, which will negatively affect the setting of the material;
• In complex joints with large deviations, it is recommended to glue a strip of small (up to 15 cm) width before gluing the main panels end-to-end. This precaution will protect the connection when joining the wallpaper and mask flaws in the event of an inaccurate fit. This method is used only for plain wallpaper without a pattern;
• For those who still have difficulty imagining how to hang wallpaper in the corners without defects, it is recommended to use non-woven wallpaper. They best mask flaws on problem surfaces;
• If folds form when smoothing the canvas, they can be carefully trimmed at an angle of 45 degrees, which will eliminate the unevenness and continue working;
• Smoothing of the panel is carried out until the air pockets are completely eliminated. Otherwise, these places will not stick and over time will lead to peeling of the entire trellis;
• When using the overlap method of joining wallpaper, followed by trimming the extra centimeters along the length, it is necessary to carefully move the joints away from the wall with a wide metal spatula and apply glue again, since when removing excess strips, the glue is also removed from the wall. It is better to trim off the excess with a utility knife, using a wide spatula as a guide.

These practical tips will allow any beginner home handyman cope with difficulties and understand how to glue wallpaper in the corners of a room without mistakes.

Matching wallpaper with a pattern

Particularly difficult is the work of wallpapering with a pattern. With minimal vertical wall errors, the joining is usually successful. The pattern may shift, but this drawback does not affect the overall picture.

To better fit the two sheets according to the pattern, it is necessary to spread both trellises on a flat surface with the front part facing up. Next, you should take measurements from the last glued sheet to the corner at the top and bottom. These distances must be set aside on the first sheet, and another 5 cm should be retreated from the received marks.

By connecting the points vertically, we get a fold line (first measurement) and a cutting line (second measurement). Along the second line, excess wallpaper is cut off.

The resulting sheet is superimposed on the second sheet intended for joining, and adjusted according to the pattern so that the minimum point along the width of the first sheet overlaps by 3-4 cm, after which the second sheet is cut to the required height.

When both sheets are ready, adhesive is applied to them and to the walls and the finished parts are applied, carefully joining them according to the pattern. The process of smoothing trellises is described in previous methods for gluing corners.

The overlap area is cut using a utility knife and a guide base (trowel), the cut strips are removed, and the joint is additionally coated with glue and rolled with a rubber roller.

Non-woven wallpaper is wallpaper made using non-woven cellulose non-woven material. Unlike paper analogues, such wallpapers are superbly washable, allow you to hide even quite noticeable wall irregularities and retain an attractive appearance for a long time. appearance. And the process of gluing non-woven wallpaper is quite simple - the material is quite docile, does not “pull” either horizontally or vertically and practically does not produce “bubbles”. And even in such “problem” places. like external and internal corners, non-woven wallpaper is pasted without any problems - for this, when gluing it is enough to follow a few simple rules.

How to glue non-woven wallpaper on internal corners

The first thing that needs to be said about gluing non-woven wallpaper in corners (both external and internal) is You shouldn’t try to cover a corner with a whole sheet of wallpaper.. In other words, do not try to cover both walls adjacent to the corner with one canvas. Otherwise, there is a fairly high probability that the wallpaper will “lead” in the corner, and the resulting wrinkles will be almost impossible to smooth out without trimming, which will certainly ruin the appearance of the wallpaper. But even if this does not happen, the curvature of the corner (and unfortunately, most of the corners in our apartments are curved) will affect the position of the canvas, and since non-woven wallpaper is glued end-to-end, all subsequent canvases will also have to be glued out of level.

The correct technology for gluing non-woven wallpaper on internal corners is as follows:

• We measure the distance from the edge of the last glued canvas to the corner and add 5 centimeters to it. A panel of exactly this width will need to be prepared for sticking in the corner.

Since the angle can be curved, it is better to measure the distance at three points: the bottom, middle and top of the wall. For calculations, of course, you need to take the largest of the resulting values.

• When the panel of the required width is ready, carefully coat the wall and corner with glue for non-woven wallpaper. Please note that when gluing non-woven wallpaper, the glue is applied only to the walls.
• After the canvas is pasted, you should very carefully smooth the wallpaper in the corner and on the next wall using a rubber roller or a dry cloth.

If the wallpaper “wrinkles” in some places, you can make several horizontal cuts at a distance of 5-10 centimeters from each other.

Please note that this canvas must be glued “overlapping” the previous canvas.

• When both canvases are pasted, all that remains is to use a wallpaper knife and a metal ruler of a paint spatula to “trim the seam.” You can learn more about the “corner trimming” technology by watching the following video.

Video about corner trimming of wallpaper

It is very important to cut both wallpaper sheets “in one step”, since otherwise discrepancies may appear in the cut line.

To ensure that the cut is even and the wallpaper does not “stretch” under the knife? You need to periodically break off the dull tip of the wallpaper knife according to the marks specially applied to the blade.

• After trimming, all that remains is to remove the excess wallpaper. Upper layer can be removed without problems, and the lower one can be removed by slightly unscrewing a small part of the upper panel.

If you did everything correctly, the panels will form an almost imperceptible joint between themselves, which will only need to be carefully smoothed using a rubber roller.

Glue on external corners

External or external corners are not found in all rooms, but, nevertheless, they can be found quite often. The technology for gluing non-woven wallpaper to such corners is practically no different from the method of gluing internal corners.

First of all, measure the distance to the corner from the outer panel and prepare new leaf wallpaper in such a way that after sticking they “turn” around the corner by no more than 5 centimeters. From the turning point closest to the corner, measure the distance for gluing the next sheet (roll width minus 1 centimeter). We glue the fabric “overlapping” onto the resulting fold, after which we trim the seam with a wallpaper knife and remove unnecessary parts of the wallpaper.

If the outer corner is fairly even (you can determine this using a plumb line), you can try to cover it with “one sheet”. But keep in mind that the level difference in this case should not exceed 0.2-0.4 centimeters. Otherwise, it is better to glue non-woven wallpaper using the technology described above.

As you can see, there is nothing difficult in gluing corners with non-woven wallpaper, so with a little practice you will be able to do this job perfectly. Good luck with your renovation!

Wallpaper is one of the most common types decorative finishing walls For wallpapering walls no need for perfect alignment. This advantage sets wallpaper apart from other materials.

Paintable wallpapers are especially versatile. But when gluing them to walls, some problems may arise. finishing of internal and external corners.

To glue the wallpaper on the corners evenly, you need strictly adhere to the recommendations of the masters. You need to start joining and pasting wallpaper in the corners by taking measurements at the bottom and top of the walls.

Non-woven wallpapers are the most popular and available materials for wall decoration. They can hide small uneven surfaces of the walls. If the walls have small flaws, it is possible that The corners may also have some unevenness.

To properly cover the corners with non-woven wallpaper, necessary:

• Measure distance from the last glued strip to the corner. To this distance you need to add about 15mm. stock;
• From the prepared strip of wallpaper cut off the resulting size when measuring the wall. After this, glue is applied to the wall and the resulting piece of wallpaper is applied;
• Now wallpaper smoothed along the wall towards the corner. Then we wrap the edge of the wallpaper onto the other wall, and also smooth it out so as to avoid unevenness or swelling of the material;
• If the strip is skewed, there is no need to re-glue it. You can safely measure out the next strip and overlap it. This operation will hide the resulting distortion;
• If the picture does not match, move the wallpaper as far as possible up or down, left or right, as far as the distance allows, to approximately align the pattern;
• Paste over the corner a whole strip is highly undesirable.

Today, wall coverings vinyl wallpaper is a fairly common way to decorate an apartment. The peculiarity of this wallpaper is that they can be washed, do not wrinkle and do not lose color or texture over time. Non-woven wallpaper has the same properties.

Vinyl wallpaper has its own features and requirements for pasting. Despite this, the methods for gluing non-woven and vinyl wallpaper are approximately the same.

To get it right cover corners with vinyl wallpaper, need to:

• Do measuring the distance to the corner and choose the method and orientation of the wallpaper stripes on the wall. You can start wallpapering from the corner, but this is done only by experienced specialists;
• Based on the result start gluing the strips wallpaper so that there is an overlap of 3 cm around the corner. After this, lubricate the wall with glue and place strip after strip all the way to the corner;
• Smoothing the pasted part of the walls in the direction of the corner;
• On coal you need to be careful grease the wallpaper and bend a piece of wallpaper, smoothing them with a thick cloth to avoid folds and unevenness;
• On the other hand, overlap joining another part of the wallpaper;
• After this, we lean the ruler or level against the overlap and cut with a sharp knife;
• Cuttings should be removed;
• Generously coat the wallpaper with glue and lean the joint against the wall. In this case, we get an evenly covered corner with vinyl wallpaper.

Pasting external corners is a very difficult task. But you shouldn’t panic that you won’t succeed. Just you need to know some tricks and methods pasting the external corners of a house or apartment.

The process of gluing strips of wallpaper on the outer corner is no different from the methods with the inner corners. This process includes several actions:

• Need to start from taking the required dimensions. We measure the distance from the corner to the last glued strip. You need to measure from above and below to determine the evenness or unevenness of the angle. We also take into account the size of the overlap at the corner of 2.5 cm;
• After that transfer the resulting size to the roll web. Having drawn the cutting lines, we cut the wallpaper and get a strip of the desired size;
• Apply glue to the wall;
• Let's take it strip and apply to the wall, smoothing it with a rubber spatula or soft cloth. We also do the same with the overlap area;

• Then the next piece is cut from the roll and glued overlapping from the corner along the wall. This method of pasting will allow you to hide possible uneven corners and stripes of wallpaper.

Also watch a master class from a specialist on how to glue and cut wallpaper in corners